CANON IR3300 ERROR CODES LIST PDF

Canon Ir Error Code List. Code Description. E Communication error ( with pedestal). E Communication error (with ASSIST). Free downloads Error Codes Canon iRPage 1 of 5 Error Codes Canon iR Download here the full version of service manual iR Code List. Thank you for purchasing the Canon iR/iR/iR Series Machine. This Manual describes the use of the List of Error Codes Without Messages.

Author: Voodoonos Gazragore
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Marketing
Published (Last): 13 November 2016
Pages: 308
PDF File Size: 2.63 Mb
ePub File Size: 13.60 Mb
ISBN: 935-2-82114-658-2
Downloads: 73839
Price: Free* [*Free Regsitration Required]
Uploader: Gumi

In the course of sensor output automatic adjustment, the light-emitting voltage is set to 4. The home position sensor does not go ON when the main power switch is turned on. The rear controller PCB is faulty. The front alignment motor relay harness is faulty.

Is it W or3300 Main cause The waste toner case is full.

Malfunction, PCBs Turn off and then on the main power switch. The pedestal main motor is faulty. Fixing film sensor Check the fixing film rotation signal. The fax PCB is faulty. Fit the DRAM securely. E When the main power is turned on, the checksum of the finisher controller PCB has a fault.

The main power supply PCB is faulty. Errr The paddle does not leave home position when the paddle motor is driven for 2 sec or more. Or, it does not reach 70C 2 sec thereafter Causes: The fixing film unit is faulty.

  AGUANTANDO JUNOT DIAZ PDF

Canon Ir 3300 Error Code List

Board Is the connection between the relay board and the main controller PCB normal? Main cause The IPC communication is faulty. Caution To reset the error, execute the following in service mode: Is the drive voltage of the heater supplied by the eerror J8 of the main power supply PCB? The puncher motor M1P is faulty.

canon ir error code Questions & Answers (with Pictures) – Fixya

E An error in the rotation of the fixing film is detected. The Card Reader-C1 is faulty. Contact Is any of the contacts of the primary charging roller, developing assembly, or transfer ir330 roller soiled?

Is the drive voltage of the heater supplied by the connector J8 of the main power supply PCB? The wiring is faulty. Is it 0 W short circuit? The aligning plate home position sensor rear; PI5 is faulty. The stack handling motor M2 relay harness is faulty.

Main cause The fixing film sensor PS45 is faulty. Is the problem corrected? The main controller PCB is faulty. State Does the scanner operate when the power is turned on? Caution To clear the error, execute the following in service mode: The return roller home position sensor S3 is faulty, the harness connector is disconnected, or an erroor circuit exits.

  E772 DELL PDF

cides

The detail codes of the fans in question are as follows: Main cause The paddle home position sensor PI2 is faulty. Caution When this code occurs, no code is indicated, but the keys are locked. The pedestal controller PCB is faulty.

The delivery motor relay harness is faulty. The puncher motor clock sensor Codrs is faulty. E The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less. The main thermistor or the sub thermistor detects overheating hardware circuit detection Causes: The sub thermistor detects about C or higher Causes: Main cause The main motor M2 is faulty.

Making Corrections Downloading system software Check the types of the BootROM and the system software, and download system software of the correct type. Replace the main power supply PCB.

Replace the scanning lamp. Main cause The connection of the IC socket is faulty. The main thermistor has an open circuit. The front aligning plate is subjected to an excess load.