Documents Similar To CINI Manual. Industrial Insulation Manual. Uploaded by. Haris Prawoto. Standard Specification for Hot Insulation (Piping & Equipment). This SPECIFICATION is based on the CINI Handbook “Insulation for Industries”, English. Version, dated 1st October (also known as the ” edition”). This section is based on the Committee Insulation Netherlands. Industry (CINI) Manual “Insulation for Industries”. DACE fol- lows the CINI standard as much as.

Author: Ner Mazurn
Country: Philippines
Language: English (Spanish)
Genre: Environment
Published (Last): 27 March 2004
Pages: 485
PDF File Size: 13.97 Mb
ePub File Size: 8.36 Mb
ISBN: 512-4-37972-518-1
Downloads: 52237
Price: Free* [*Free Regsitration Required]
Uploader: Nejin

Pressure vessel basics for all engineers Pressure vessel basics for all engineers by Sharjeel Aslam Faiz 1. These couplings are furnished with restraint rings that, when affixed. Typical drawings of non-contact insulation have been added. The inner side of the inner layer shall be provided with a high temperature anti-abrasive compound, based on a mixture imdustries calcium industriee hemihydrates and Portland cement for temperatures up to o C.

What is Static Electricity? Drawings and general provisions of the Contract, More information. The potential cost and safety implications are enormous, and therefore insulation systems shall be designed according to categories that indicate vulnerability to CUI and are related to the process temperatures. Also acoustic insulation is included. Category System and Material Guidance 1 Note: The Principal may also include an agent or industriea, authorised to act for the Principal.

Drainage outlets should be provided to give visible indication of possible valve or flange leakage. The product should be delivered on site in two components ready for use. Extent of mechanical insulation required by this section is indicated on drawings and schedules, and by requirements of this section. These couplings are furnished with restraint rings that, when ffor More information. Undustries hot insulation around flanges, valves, etc.

Insulation collars, if not provided by the equipment Vendor, shall be fitted to avoid any water ingress see Appendix 9.

  LEY 189-11 PDF

The CINI Manual is a standard for insulation companies, industrial companies, their staff and consultants to achieve optimal quality of insulation systems.

Roof coverings More information. The possibility of insulqtion insulation has also been included.

And, most importantly, how can it be controlled? Pipes laid in the ground must be introduced into concrete walls or shafts. Shell Global Indusyries International B.

Other systems are available for specific uses. Quick-release toggles shall not be fitted in overhead lines above walkways.


In that case the joints shall be finished in the field. Consequently, three categories of users of DEPs can be distinguished: All materials and application methods shall be selected to suit local weather and environmental conditions. Alternatives shall be submitted to the Principal for approval and shall be supported by references e.

If metal jacketing is used, sufficient space invustries drainage shall be provided to avoid internal accumulation of water caused by condensation, water vapour diffusion, capillary action and water ingress. Table of Industriez Page: Supports shall be designed to withstand all service loads. In general this means that aluminised steel or stainless steel jacketing shall be applied. Section includes, but is not limited to, design and furnishing portable davits, davit sleeves, dvit bases, four 4 removable outriggers.

TICP programs shall be used to mamual the economic insulation thickness. Cavity Drain R20 is manufactured from1.

Depending upon the indistries application the design, construction, inspection, More information. A report shall be made available which indicates the design parameters necessary to arrive at an economically and technically acceptable design.

TICP and shall be subject to the approval of the Principal.

CINI Manual – Insulation for Industries

The changes mentioned in the other parts have been implemented. This standard is intended to provide useful information to the Professional Service Provider PSP to establish a basis of design.


Personnel protection for cold insulation is normally not required, only if indicated by the Principal. The responsibility of the engineer is More information. Neither the whole nor any part of this document may be disclosed to any third party without the prior written consent of Shell International Oil Products B. Tentative sizes must be allocated to each structural More information. The metal jacket mould shall indystries installed with overlaps of at least 50 mm over the preformed spacers with temporary bands; vapour barrier jacketing shall be installed with bands and with all joints and overlaps sealed.

CINI Manual Industrial Technical Insulation

All work specified in this Section is subject to the provisions of Section Subject to any particular terms and conditions as may be set forth in specific agreements with users, Shell GSI, SIEP and SIC disclaim any liability of whatsoever nature for any damage including injury or death suffered by any company or person whomsoever as a result of or in connection with the use, application or implementation of any DEP, combination of DEPs or any part thereof, even if it is wholly or partly caused by negligence on the part of Shell GSI, SIEP or other Service Company.

Fabrication, furnishing and installation of chain link fence, chain link gates, and extension brackets with barbed wire. The adhesives shall withstand any stresses and strains, accommodate contraction within the foam and remain effective within the required temperature range.

The protection shall be restricted to a distance of not more than mm horizontally from access walkways and normal working areas.

Insulation materials shall be free of asbestos.