DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.
|Published (Last):||17 June 2016|
|PDF File Size:||11.33 Mb|
|ePub File Size:||20.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. E and eA are measured with the leads constrained to be perpendicular to datum -C. Putere n-am, Tu-mi fii sprijin. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
In the OFF state each channel blocks voltages up to the supply rails.
DGABK Datasheet, PDF – Alldatasheet
In case of conflict between English and Metric dimensions, the inch dimensions control. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. Copyright Intersil Americas Inc. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off.
The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
An enable input is provided. In either case, source-to-body diodes can be forward biased and conduct current from the signal source.
DGABK (MAXIM) – Quad SPST CMOS Analog Switches
Dimensions b1 and c1 apply to lead base metal only. Dimension Q shall be measured from the seating plane to the base plane. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.
Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with dataseet positive and negative supplies as shown in Figure 2. For more information on TYP values see Note 3.
Maxim guarantees that these switches will not latch up if the power supplies are disconnected datssheet input signals still connected. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. Typical values are for design aid only, not guaranteed and not subject to production testing. Asa cum sunt, la Tine vin! The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns.
All Rights Reserved All other trademarks mentioned are the property of their respective owners. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. B1 maximum dimensions do not include dambar protrusions.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. For the latest package outline information, go to www. No circuit patent licenses are implied. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform.
Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Dimension M applies to lead plating and finish thickness. D, D1, and E1 dimensions do not include mold flash or protrusions. Limit diode current to maximum current ratings. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.
DG201A, DG211 Quad SPST CMOS Analog Switches
N is the maximum number of terminal positions. This dimension allows for off-center lid, meniscus, and glass overrun. Information furnished by Intersil is believed to be accurate and reliable. For more information on TYP values see Note 2. VO is the steady state output with switch on. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Parameter guaranteed by design or characterization. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.
SR Datasheet – Micropower Direct. Maxim reserves the right to change the circuitry and specifications without notice at any time. For information regarding Intersil Corporation and its products, see www.
Lab 6 in this note. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. Mold flash or protrusions shall not exceed 0.
Dambar protrusions shall not exceed 0. Device mounted with all leads soldered to PC board.
Documents Flashcards Grammar checker. For this configuration dimension b3 replaces dimension b2. Measure dimension S1 at all four corners.