Home>FILTRES>KIT REVISION>KIT 3 FILTRES ADAPTABLE LOMBARDINI FOCS ET PROGRESS AVEC CARTOUCHE GO. (except where indicated in this manual). • Stop the engine before Diesel engine: LOMBARDINI mod. LDW FOCS • Keep the diesel engine running . FOCS Workshop Manual_cod. _1° ed_ rev. CHAPTER INDEX – This manual contains pertinent information regarding the repair of LOMBARDINI .

Author: Tule Faet
Country: Estonia
Language: English (Spanish)
Genre: Photos
Published (Last): 21 September 2016
Pages: 308
PDF File Size: 3.72 Mb
ePub File Size: 17.75 Mb
ISBN: 683-2-34971-316-6
Downloads: 81154
Price: Free* [*Free Regsitration Required]
Uploader: Tygokree

With 2 camshaft on the cylinder head. Adjust the position of the accelerator lever via the regulator block, so that the internal adjusting nut 2, is about 5 mm from the end of the thread.

Remember me Forgot password? If turned clockwise, injection is advanced. Make sure that the ground or floor on which the machine is standing has not soaked up any fuel or oil. When reassembling, replace the seals 2.


Crankcase Breather Ldw Using piston ring compression pliers, introduce the piston into the cylinder so that combustion chamber A is directly under the precombustion chamber parallel to the head.

LDW engine the exhaust For rocs calibration of the E. Particular care is required to prevent burns. Oil Filter Cartridge Replace it if it exceeds 92 mm. Compress air at a pressure of 1 bar for about two minutes.


Block then the locknut. Do not tamper with any devices to alter the level of performance guaranteed by the manufacturer. Routine Engine Maintenance It is advisable to apply a few drops of silicon sealant on the surface of the gasket slot 2.


As well as lowering the freezing point, the permanent liquid also raises the boiling point. Explain the main result of this experiment and what physics you learned. If the calculated value is less than Valve Stem Sealing Rings – Reassembly Starter Motor – Bosch Dw 12v 1,1 Kw Codes are usually printed-out on the oil container and the understanding of their meaning is useful for comparing different brands and choosing the kind with the right characteristics.

Once the check has been completed, remove the gasket and refit the O-ring. Indeed, under torque, spring N operating lever L overcomes the resistance of spring M located in the plunger barrel. The whole surface of the cylinder affected by contact with the piston rings must be rendered with the plateau method.

Lombardini LDW 903 Manuals

Starter Motor, Bosch 12v 1,6 Kw When the crankshaft timing pulley lombarxini is vertical, the oil pump drive keyway A will be at 3: Diesel Engine Oil CF.

Alternator, Iskra 14v 33a See “Camshaft timing – Belt Tightening and Fastening”. To determine the piston clearance and, by consequence, which copper gaske is most suitable it is necessary to consider the A value of the piston that projects furthest. Before reassembling it, check value A 45 to 46 mm and the parallelism of the two levels B that must not exceed 0. When refitting tighten the screws at 80 Nm.


Replace the O-ring 1. Camshaft timing pulley – reference marks. Then rotate the crankshaft until the TDC is read in the dial gauge. Thoroughly dry any spilt fuel and move the fuel container away along with any rags soaked in fuel or oil.

Start entretifn engine and check how pressure is affected by oil temperature. The dimensions for the diesel engine generator sets are simply reference values.

Interchangeable Core Accessory focw Service Parts. These fuels reduce the formation of paraffin in diesel at low temperatures. See page 45 Aluminium connecting rod with 35 Nm tightening torque. Assess any wear caused by the lip of the seal ring on the pulley tang.

Unscrew the fastening screws that fix the flange to the engine crankcase and remove it. Insert the two pin stop rings and check that they are properly housed in their seats see fig. Maintenance – Recommended Oil Type – Refilling D For tightening torque see figures Tighten the two fuel pump fastening nuts at 24 Nm.